Free Web Hosting Provider - Web Hosting - E-commerce - High Speed Internet - Free Web Page
Search the Web


CU- and A-CU- Series
Manual and Automatic Spray Guns
Specifications
  • CU- and A-CU- Models require 3 to 24 C.F.M. at 40 to 50 lbs. air pressure depending on Head size selected. 
           
    These models have 3/8" NPT Fluid Inlet and 1/4" NPT Air Inlet. 
      
     The Fluid Body can be rotated for use with Gravity and Siphon Cup Assemblies or pressure fluid feed from Tank. By changing the Fluid Body it can be used with a Circulating System.
       
  • CF- Multipleheads produce a fan pattern for broad coverage.
           
  • CFH- Multipleheads are High Volume Low Pressure producing high transfer efficiency fan patterns.
           
  • CR- Multipleheads produce a round pattern for narrow trim work, coating inside recesses or crevices with fluid materials of medium to heavy consistency.
           
  • CRIF- Multipleheads produce internal mix external fan for less mist. (Sizes 0,2 and 4 only)
           
  • Multipleheads produce Internal mix External fan for less mist.
    CF-, CFH-, CR- and CRIF- Multiplehead Sizes:
    • CU Spray Guns provide a coating range from line to fan pattern up to 18" wide, when held 8" to 10" from the surface to be coated.
    • Note: Pages 4 and 11 will assist with your Multiplehead selection.

Manual Model CUF, CUHF and CUR

CUF- and CUR- Spray Guns are the most versatile available; with Multipleheads that convert into 29 different sizes of Paasche Manual Spray Guns. They are also available with Extensions and Elbows that reach almost anywhere your job requires. CUHF- Spray Gun High Volume Low pressure with high transfer efficiency for today’s demanding regulatory requirements. Shipping Weight: 1 lb. 6 oz. (.62k)

Automatic Model A-CU

A-CU- Automatic Spray Gun is recommended for use with medium to heavy consistency materials, for high speed coating and finishing. Shipping Weight: 1 lb. 6 oz. (.62k)

Model F87-CUADF

F87-CUADF- has an Exclusive Three-Dial Control. All three controls are independent of each other. Fluid, Atomizing and Fan Pattern Controls, require only one (1) air line to save set-up time, material and air. This Spray Gun uses the Same Aircaps and Tips as the A-CU Model. Shipping Weight: 2 lbs. (.9k)

Applications Fluid to be used CU- or A-CU- Series Multiplehead Air Cap Size Fluid Tip Minimum C.F.M. Air Comp. (H.P.) Needle Type and Size
Number Orifice Size 30 40 Manual Automatic
High Volume Low Pressure (HVLP) for CUHF- Manual Spray Gun. Maximum 50 lbs. line pressure controlled 10 lb. Head Pressure. B
B
B C
B C
C D		 * *
CUHF-		 CFH-000
CFH-00
CFH-0
CFH-2
CFH-4		 U-000
U-00
U-0
U-2
U-4		 .028
.040
.055
.073
.093		 6 7 2 u-2-3/8"  
Low Pressure Guns. High speed production using Medium to Heavy Fluids. Also general maintenance and painting. B
*

CUF-		 CF-000-3
CUF-000-4-6
CUF-000-9-3
CUF-00-4
CUF-00-4-6
CF-00-6
CF-00-9
CF-00-9-3		 U-000
U-000
U-000
U-00
U-00
U-00
U-00
U-00		 .028
.028
.028
.040
.040
.040
.040
.040		 3
4
9
4
4
6





9
9		 1/2
1
1
1

1-1/2
2
2


U-2-3/8"


A-U-4"
Medium Pressure Gun. High production using medium to heavy fluids. Atomizes heavy fluids more finely than Low Pressure Guns.


B
C

*

CUF-		 CF-0-6
CF-0-9
CF-0-12
CF-0-16
CF-2-8
CF-2-12
CF-2-15-3
CF-2-16
CF-2-20		 U-0
U-0
U-0
U-0
U-2
U-2
U-2
U-2
U-2		 .055
.055
.055
.055
.073
.073
.073
.073
.073		 6
9
12
16
8
12
15
16
20		 1-1/2
2
3
5
2
3
5
5
5



U-2-3/8"



A-U-4"
Medium Pressure Gun.High production using medium to heavy fluids. Atomizes heavy fluids more finely than Low Pressure Guns.


C
D
*

CUF-		 CF-4-6
CF-4-10
CF-4-12
CF-4-15
CF-4-20
CF-4-20-3
CF-4-24-3		 U-4
U-4
U-4
U-4
U-4
U-4
U-4		 .093
.093
.093
.093
.093
.093
.093		 6
10
12
15
20
20
24		 1-1/2
3
3
5
5
5
7


U-2-3/8"


A-U-4"
Stainless Steel Fluid Assemblies, Tip and Needle for applying latex, acids and other corrosive material. B
C		 *
CUSF-		 CFS-0-6
CFS-0-9
CFS-2-8		 U-0
U-0
U-0		 .055
.055
.070		 6
9
8		 1-1/2
2
2
U-2-3/8"
A-U-4"
Stainless Steel Fluid Assemblies, Tip and Needle for applying latex, acids & other corrosive materials.
C
G
*
CUSF-		 CFS-4-10
CFS-4-15
CFS-4-20
CFS-4-20-3		 U-4
U-4
U-4
U-4		 .098
.098
.098
.098		   10
15
20
20		 3
5
5
5
U-2-3/8"
A-U-4"
Latex, acids and corrosive fluids. Stainless Steel construction. Carbide Insert, Tip and Needle. B
C		 *
CUCF-		 CCF-00-4
CCF-0-9		 UC-00
UC-0		 .042
.055		 4
9		   1
2
UC-2-3/8"
A-UC-4"
E
F		 *
CUCF-		 CCF-2-8
CCF-4-10		 UC-2
UC-4		 .070
.098		   8
10		 2
3
UC-2-3/8"
A-UC-4"
Narrow trim work. Coating inside crevices, with medium to heavy fluids. External Round Patterns Only. B
C
*
CUR-		 CR-00-3
CR-0-4
CR-2-5		 U-00
U-0
U-2		 .040
.055
.073		 3
4
5		   1/3
1
1
U-2-3/8"
A-U-4"
C & G CR-4-6 U-4 .093 6   1-1/2 U-2-3/8" A-U-4"
Broad surface coverage. Sprays Internal mix External fan pattern. Uses 1/2 air volume of Atomizing Guns producing less mist. B
C
**
CURIF-

CURIF-		 CRIF-0-4
CRIF-2-5		 U-0
U-2		 .055
.073		 4
5		   1
1
U-2-3/8"
A-U-4"
C & G CRIF-4-6 U-4 .093 6   1-1/2 U-2-3/8" A-U-4"
* Fluid Feed Method - Gravity, Siphon or Pressure.
** Fluid Feed Method - Pressure Only.

 

CU-Series Standard Independent Atomizing Circulating Fluid Circulating & Atomizing
Fluid Body CU-7B CUA-7B CUG-7B CUGA-7B
F87-CUADF Fluid Body 87-20      
Stainless Steel Sluid Body CUS-7B CUSA-7B CUSG-7B CUSGA-7B
Stainless Steel - Solid CUSS-7B CUSSA-7B   CUSSGA-7B